Aeroneb Go Manual de instrucciones

Instruction Manual

6CLASSIFICATIONS AND MARKINGSThe symbols that appear on the Aeroneb® Go Nebulizer and its accessories are described in the table below:Symbol MeaningA

7AERONEB® GO SYSTEM PARTS:Medication Cup CapMouthpieceNebulizer bodyCableBaseControl Module AC/DC Adapter** Available with complete Aeroneb® Go System

8ASSEMBLY/FUNCTIONAL TEST1. Connect the Medication Cup to the Nebulizer Body by lining up the notches on the medication cup and nebulizer body.NOTE:

9HOW TO OPERATE THE AERONEB® GO NEBULIZER3 x AA LR61. Turn the Aeroneb® Go Control Module upside down. Slide the battery cover in the direction of th

10 5. Alternatively, you can power the device by using the AC/DC Adapter if provided (refer page 7). Plug the AC/DC adapter into a standard AC electr

11CLEANING AND STORING YOUR AERONEB® GOAFTER EVERY USE:Disconnect the control module before you take the nebulizer apart to rinse it.1. Rinse the Neb

12OPTIONAL DISINFECTION:If you would like to disinfect your Aeroneb® Go Nebulizer, you may choose one of the following two options; Boiling or Vinegar

13OPTIONAL DISINFECTION2. VINEGAR SOLUTION:i. Rinse the Nebulizer Unit (Medication Cup, Nebulizer Body, Base and Mouthpiece or Mask Adapter) under r

14TROUBLESHOOTING GUIDEIf you have difculty operating your Aeroneb® Go, check the following points:Problem Check RemedyNo visible aerosol when using

15Problem Check RemedyCheck that the AC/DC Adapter is not faulty.Try to operate the Control Module by using batteries instead of the AC/DC Adapter. If

16WARNINGS:• Only use the Aeroneb® Go nebulizer with components specied in the Instructions for Use. Use of the Aeroneb® Go nebulizer with component

17SPECIFICATIONSPhysicalAeroneb Go nebulizer unit (assembled): 40 x 105 x 95 mmAeroneb Go Control Module: 70 x 110 x 32 mmAC/DC adapter: 74 (H) x 72 (

18PERFORMANCE:Aerosol ow rate: > 0.3 mL/minAverage tested ow rate: 0.4 mL/minParticle Size:As measured with the Andersen Cascade Impactor:- Spec

19Representative particle size distribution graph for Albuterol as per EN13544-1 is shown below:Aerodynamic Size (µm)0.1 1 10 100100.050.00.0Cumulat

20REPLACEMENT PARTS AND ACCESSORIES:PART REORDER NUMBERAeroneb® Go System AG-AG4200-XX*Medication Cup Cap AG-AG3010Aeroneb® Go Handset AG-AG4300Mouthp

21Appendix 1EMC tables: The following Tables are provided in accordance with IEC/ EN 60601-1-2:Guidance and manufacturer’s declaration – electromagnet

Recommended separation distances between portable and mobile RF communication equipment and the Aeroneb GoThe Aeroneb Go nebulizer system is intended

Guidance and manufacturer’s declaration – electromagnetic immunityThe Aeroneb Go nebulizer system is intended for use in the electromagnetic environme

Immunity test IEC/EN 60601 Test levelCompliance level Electromagnetic environment – guidancePower frequency (50/60 Hz)Magnetic eldIEC 61000-4-83 A/m

Guidance and manufacturer’s declaration – electromagnetic immunityThe Aeroneb Go nebulizer system is intended for use in the electromagnetic environme

Table of ContentsIntroduction ... 1Important Safeguards ... 2W

This page has been intentionally left blank

©2013 Aerogen LimitedAG-AG4120-EN Rev D 2013 Manufacturing no.: 30-553 Rev D Aerogen Limited,Galway Business Park,Dangan,Galway,Ireland.www.aerogen.c

This page has been intentionally left blank

1INTRODUCTION Be sure to read these instructions fully before use.Thank you for purchasing the Aeroneb® Go Nebulizer. Certain conditions such as asthm

2IMPORTANT SAFEGUARDSWhen you use electrical products, always follow basic safety precautions. As with any electrical device take particular care arou

3• Do not use components or attachments that are not recommended by Aerogen. Refer to the Replacement Parts and Accessories section in this manual (p

4• Do not nebulize alcohol-based drugs in an oxygen-rich/high pressure environment.• In event of loss of mains power, remove the AC/DC cable from th

5WARRANTYThe Aeroneb® Go Control Module and AC/DC Adapter are warranted for a period of two years from the date of purchase against defects in manufac